boosternowbot

The Johnson-Evinrude Workshop manual downloads for the above listed models describes the service procedures for the complete vehicle. Follow the Maintenance Schedule recommendations to ensure that the outboard is in peak operating condition. Performing the scheduled maintenance is very important. It compensates for the initial wear that occurs during the life of the outboard motor. All chapters in the Workshop Manual apply to the whole vehicle and illustrates procedures for removal/installation of components that are in detailed step-by-step fashion. Most all Workshop manual chapters start with an assembly or system illustration, diagrams, exploded parts view, pictures, service information and troubleshooting for the section.

1. Johnson Evinrude Repair Manual Free
2. Evinrude 135 Hp Outboard

The subsequent pages give detailed procedures. PROBLEM 1: ENGINE TURNS OVER BUT WILL NOT START OR STARTS HARD WHEN COLD Possible Cause Corrective Action Improper starting procedure. Check procedure, as outlined in “Operation and Maintenance Manual.” Fuel tank empty; improperly mixed fuel; contaminants (water, dirt, etc.) in fuel. Check fuel in fuel tank and replace or add. Fuel tank air vent closed or restricted. Air vent must be open and free from contaminants.

A pinched or restricted fuel line. Check, and replace as needed. Dirty or restricted fuel filter. Check, replace or clean. Enrichener valve not operating. Check enrichener system.

(Refer to “Enrichener System” following.) An inlet needle (in carburetor) that is stuck open or closed. (A needle stuck open, will cause a flooding condition.

A needle stuck closed, will prevent fuel from entering carburetor.) Remove, clean, or replace. Anti-Siphon valve restricting fuel flow.

Refer to “Checking for Restricted Fuel Flow caused by Anti-Siphon Valves”, following. See “Checking for Restricted Fuel Flow caused by Anti-Siphon Valves”, page 3A-1. PROBLEM: ENGINE FLOODS Possible Cause Corrective Action Dirt or foreign particles are preventing inlet needle from seating. Flush out inlet seat and clean inlet needle. Worn inlet needle. Punctured float.

Incorrect float setting. PROBLEM: ENGINE RUNS TOO LEAN Possible Cause Corrective Action Carburetor is loose. Air leaks past mixing chamber cover. Tighten bolts securely. Tighten cover or replace gasket.

Fuel level too low. Reset float level. Clogged high speed jet. Check and clean.

Restricted fuel flow to carburetor. Check fuel lines and filter(s) for restricted flow. Incorrect high speed jet. Refer to main jet chart and replace with proper jet. Idle mixture set too lean.

Adjust to run richener. Air leakage into fuel system. Check fuel line connections, hose clamps, fuel pump, and fuel outlet tube (located in fuel tank) for loose fittings.

Anti-Siphon valve restricting fuel flow. Refer to “Checking for restricted fuel flow caused by Anti-Siphon valves.” PROBLEM: ENGINE RUNS TOO RICH Possible Cause Corrective Action Fuel level too high. Reset float to correct level. Carburetor floods. See preceding “Engine Floods” Idle nozzle air holes plugged. Blow out with compressed air. Restricted air flow.

Check cowl air inlet and carburetor for obstructions. Main Fuel Jet loose. Retighten Jet. PROBLEM 1: ENGINE IDLES ROUGH AND STALLS PROBLEM 2: ENGINE RUNS UNEVEN OR SURGES PROBLEM 3: ENGINE WILL NOT ACCELERATE Possible Cause Corrective Action Fuel tank air vent closed or restricted. Check - Air vent must be open all-the-way and free from restrictions.

A pinched, cut or restricted fuel line; also loose fuel line connection. Check all fuel lines and replace as needed.

Check and tighten all fuel line connections. A dirty or restricted fuel filter. Check, replace, or clean all fuel filters. Restricted filter in fuel tank. Clean by rinsing in clean lead-free gasoline or kerosene.

Improperly mixed fuel; contaminants (water, dirt, etc.) in fuel. Check fuel and replace, if necessary. An inlet needle (in carburetor) that is either stuck open or closed. (A needle, that is stuck open, will cause a flooding condition.

A needle, that is stuck closed, will prevent fuel from entering carburetor.) Remove and replace with new inlet needle. Incorrect idle mixture adjustment. Damaged fuel pump diaphragm.

Carburetor is loose. Tighten bolts securely. Chamber cover leaking air.

Tighten or replace gasket. Off idle holes plugged. Blow out with compressed air. Main nozzle or idle nozzle air bleed holes plugged. Blow out with compressed air. Improper main jet or restricted jet. Clean or replace with proper jet (refer to “Main Jet Chart”).

Damaged reed(s). Inspect reeds as outlined in Section 4A. A crack in the fuel pick-up outlet tube (located in fuel tank). A crack in the fuel outlet tube (located in fuel tank.) Replace.

Anti-Siphon valve restricting fuel flow. Refer to “Checking for Restricted Fuel Flow Caused by Anti-Siphon Valves,” following.

PROBLEM: FUEL BLOW-BACK OUT OF CARBURETOR Possible Cause Corrective Action Chipped/Broken (reed-block) Reeds Replace Reeds. PROBLEM: ROUGH IDLE If related to reed-block, indicates excessive preload in reeds. Replace Reeds.

PROBLEM: CAN’T REDUCE ENGINE RPM TO SLOW IDLE Multiple Chipped Reeds. Replace Reeds.

Checking for Restricted Fuel Flow Caused by Anti-Siphon Valves While anti-siphon valves are helpful from a safety standpoint, they clog, they may be too small, or they may have too heavy a spring. The pressure drop across these valves can, create operational problems and/or powerhead damage by restricting fuel. Some symptoms of restricted (lean) fuel flow, are: 1. Loss of fuel pump pressure 2. Loss of power 3.

High speed surging 4. Preignition/detonation (piston dome erosion) 5.

Outboard cuts out or hesitates upon acceleration 6. Outboard runs rough 7.

Outboard quits and cannot be restarted 8. Outboard will not start 9.

Johnson Evinrude Repair Manual Free

Vapor lock Any type of anti-siphon device must be located between the outboard fuel inlet and fuel tank outlet. A method of checking if such a device (or bad fuel) is a problem source is to operate the outboard with a separate fuel supply which is known to be good. If, it is found that the anti-siphon valve is the cause of the problem, either 1) replace the anti-siphon valve or 2) replace it with a solenoid-operated fuel shutoff valve. 1973 1990 Johnson Evinrude 2 to 40 HP Service Manual Outboard Johnson - Evinrude Service Manual Application: 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990 Outboard For 2, 2.5, 4, 4.5, 5, 6, 7.5, 8, 9.5, 9.9, 15, 18, 20, 25, 28, 30, 35, 40 HP (Horsepower - Horse Power) Outboards Marine Engine Johnson/Evinrude 2Stroke 2-Stroke Two Stroke & 4Stroke 4-Stroke Four Stroke models.

1973-1990 Johnson Evinrude Service Manual 48 235 HP Outboard & Sea Drives Johnson - Evinrude Service Manual Application: 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990 Outboard & Sea Drive (Sea Drives) For 48 50 55 60 65 70 75 85 88 90 100 110 115 120 135 140 150 175 185 200 225 & 235 HP (Horsepower - Horse Power) Outboard & Sea Drive Marine Engine Johnson/Evinrude 2Stroke 2-Stroke Two Stroke & 4Stroke 4-Stroke Four Stroke models.

1973 Johnson Evinrude 135 HP Outboard Service Manual PDF Download 1973 Johnson Evinrude 135 HP Outboard Service Manual 1973 Johnson Evinrude 135 HP Outboard Service manuals are available for immediate download. This service is available for only $4.95 per download! If you have a dirty old paper copy of this manual or a PDF copy of this manual on your computer and it crashed we can help! Your 1973 Johnson Evinrude 135 HP Outboard Service manual will come to you in pdf format and is compressed for a lightning fast download! After downloading your 1973 Johnson Evinrude 135 HP Outboard Service manual you can view it on your computer or print one or all of the pages needed.

You can pay for your 1973 Johnson Evinrude 135 HP Outboard Service manual with Paypal or Visa, MasterCard or Discover. Immediately upon payment you will automatically be forwarded to our secure download page. We will also send you an email with a copy of your 1973 Johnson Evinrude 135 HP Outboard Service manual download link. 1973 Johnson Evinrude 135 HP Outboard Service manuals - the easy way! Johnson Evinrude Service Manuals Please visit our brand new to see a complete list of all available Johnson Evinrude outboard service manuals. Please visit our to see a complete list of all the useful service manuals we offer. 'Service Manual' is a generic term we use to describe Repair Manuals, Technical Manuals, Workshop Manuals, Shop Manuals, etc.

Evinrude 135 Hp Outboard

Customer Service 1973 Johnson Evinrude 135 HP Outboard Service Manual Johnson Model 135ESL73 / V4 / 99.6 CI Evinrude Model 135383 380 pages are in.pdf format 68 MB in.zip format for super fast downloads! Your Instant Download Price is Only $4.95.